20241102解决荣品PRO-RK3566开发板刷Rockchip原厂的Buildroot使用荣品的DTS出现
20241102解决荣品PRO-RK3566开发板刷Rockchip原厂的Buildroot使用荣品的DTS出现fiq_debugger问题
2024/11/2 9:46
缘起：给荣品PRO-RK3566开发板刷Rockchip原厂的Buildroot时，DEBUG波特率是1.5Mbps。
但是启动到FIQ阶段，在你使用荣品的DTS的时候，就会切换到115200bps。
调试的时候，肯定/100%要求是固定在一个默认波特率上。
因此就直接以Rockchip原厂的1.5Mbps为准了。
初步判定：Rockchip原厂的Buildroot默认波特率是1.5Mbps N 8 1
荣品的DTS配置DEBUG的默认波特率是115200bps N 8 1
直接通过grep查找115200，把找到的地方都修改/屏蔽掉即可。
Z:\RK3566_RK3568_Linux5.10_V1.2.0\kernel\arch\arm64\boot\dts\rockchip\pro-rk3566.dts
test-power {
/** disable for use rk809-battery */
status = "disabled";
};
charge-animation {
compatible = "rockchip,uboot-charge";
rockchip,uboot-charge-on = <0>;
rockchip,android-charge-on = <0>;
rockchip,uboot-low-power-voltage = <7000>;
rockchip,screen-on-voltage = <7000>;
status = "okay";
};
//fiq-debugger {
// compatible = "rockchip,fiq-debugger";
// rockchip,serial-id = <2>;
// rockchip,wake-irq = <0>;
// /* If enable uart uses irq instead of fiq */
// rockchip,irq-mode-enable = <1>;
// rockchip,baudrate = <115200>; /* Only 115200 and 1500000 */
// interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_LOW>;
// pinctrl-names = "default";
// pinctrl-0 = <&uart2m0_xfer>;
// status = "okay";
//};
};
&pmu_io_domains {
status = "okay";
pmuio2-supply = <&vcc3v3_pmu>;
vccio1-supply = <&vccio_acodec>;
vccio3-supply = <&vccio_sd>;
vccio4-supply = <&vcc_3v3>;
vccio5-supply = <&vcc_3v3>;
vccio6-supply = <&vcc_1v8>;
vccio7-supply = <&vcc_3v3>;
};
1.5Mbps波特率：
[BEGIN] 2024/11/2 9:37:29
DDR 2d653b3476 typ 24/01/20-15:04:19,fwver: v1.21
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: 48ps, dqs1: -120ps, dqs2: -72ps, dqs3: -192ps,
tdqss: cs1 dqs0: -24ps, dqs1: -120ps, dqs2: -72ps, dqs3: -168ps,
change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x62
rx vref: 22.4%
tx vref: 38.0%
change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
rx vref: 28.4%
tx vref: 36.0%
change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
rx vref: 15.6%
tx vref: 32.0%
change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x38
rx vref: 15.6%
tx vref: 19.8%
cs 0:
the read training result:
DQS0:0x3e, DQS1:0x40, DQS2:0x44, DQS3:0x3a,
min : 0xb 0xb 0xe 0xb 0x1 0x2 0x6 0x5 , 0x8 0x9 0x2 0x1 0xd 0xb 0xc 0xa ,
0x11 0xf 0xf 0xd 0x4 0x1 0x4 0x8 , 0xb 0x9 0x6 0x1 0xc 0xe 0x9 0xe ,
mid :0x2a 0x2a 0x2b 0x2a 0x1f 0x20 0x24 0x23 ,0x27 0x28 0x22 0x20 0x2b 0x2a 0x2b 0x29 ,
0x30 0x2e 0x2d 0x2c 0x23 0x20 0x21 0x25 ,0x29 0x27 0x24 0x20 0x2a 0x2c 0x28 0x2c ,
max :0x49 0x49 0x49 0x49 0x3e 0x3f 0x42 0x42 ,0x47 0x48 0x42 0x40 0x49 0x4a 0x4a 0x48 ,
0x50 0x4e 0x4b 0x4c 0x42 0x3f 0x3f 0x43 ,0x48 0x45 0x43 0x3f 0x49 0x4b 0x47 0x4a ,
range:0x3e 0x3e 0x3b 0x3e 0x3d 0x3d 0x3c 0x3d ,0x3f 0x3f 0x40 0x3f 0x3c 0x3f 0x3e 0x3e ,
0x3f 0x3f 0x3c 0x3f 0x3e 0x3e 0x3b 0x3b ,0x3d 0x3c 0x3d 0x3e 0x3d 0x3d 0x3e 0x3c ,
the write training result:
DQS0:0x35, DQS1:0x28, DQS2:0x2f, DQS3:0x22,
min :0x58 0x5c 0x5c 0x5b 0x51 0x54 0x53 0x53 0x56 ,0x4a 0x4a 0x43 0x44 0x4d 0x4d 0x4e 0x4c 0x4a ,
0x5c 0x5c 0x58 0x58 0x54 0x51 0x50 0x55 0x58 ,0x50 0x50 0x4d 0x4a 0x55 0x55 0x4e 0x54 0x4e ,
mid :0x73 0x76 0x77 0x75 0x6b 0x6d 0x6e 0x6e 0x71 ,0x65 0x65 0x5f 0x5f 0x68 0x68 0x69 0x67 0x66 ,
0x77 0x77 0x73 0x73 0x6d 0x69 0x6a 0x6f 0x72 ,0x6c 0x6a 0x68 0x64 0x6f 0x6f 0x6a 0x6e 0x6a ,
max :0x8e 0x90 0x92 0x90 0x86 0x86 0x8a 0x8a 0x8c ,0x81 0x80 0x7b 0x7a 0x84 0x83 0x84 0x83 0x82 ,
0x93 0x92 0x8e 0x8f 0x87 0x82 0x84 0x8a 0x8d ,0x89 0x84 0x84 0x7f 0x89 0x89 0x87 0x89 0x87 ,
range:0x36 0x34 0x36 0x35 0x35 0x32 0x37 0x37 0x36 ,0x37 0x36 0x38 0x36 0x37 0x36 0x36 0x37 0x38 ,
0x37 0x36 0x36 0x37 0x33 0x31 0x34 0x35 0x35 ,0x39 0x34 0x37 0x35 0x34 0x34 0x39 0x35 0x39 ,
cs 1:
the read training result:
DQS0:0x3e, DQS1:0x40, DQS2:0x44, DQS3:0x3a,
min : 0xb 0xb 0xe 0xb 0x1 0x2 0x6 0x5 , 0x8 0x9 0x2 0x1 0xd 0xb 0xc 0xa ,
0x11 0xf 0xf 0xd 0x4 0x1 0x4 0x8 , 0xb 0x9 0x6 0x1 0xc 0xe 0x9 0xe ,
mid :0x2a 0x2a 0x2b 0x2a 0x1f 0x20 0x24 0x23 ,0x27 0x28 0x22 0x20 0x2b 0x2a 0x2b 0x29 ,
0x30 0x2e 0x2d 0x2c 0x23 0x20 0x21 0x25 ,0x29 0x27 0x24 0x20 0x2a 0x2c 0x28 0x2c ,
max :0x49 0x49 0x49 0x49 0x3e 0x3f 0x42 0x42 ,0x47 0x48 0x42 0x40 0x49 0x4a 0x4a 0x48 ,
0x50 0x4e 0x4b 0x4c 0x42 0x3f 0x3f 0x43 ,0x48 0x45 0x43 0x3f 0x49 0x4b 0x47 0x4a ,
range:0x3e 0x3e 0x3b 0x3e 0x3d 0x3d 0x3c 0x3d ,0x3f 0x3f 0x40 0x3f 0x3c 0x3f 0x3e 0x3e ,
0x3f 0x3f 0x3c 0x3f 0x3e 0x3e 0x3b 0x3b ,0x3d 0x3c 0x3d 0x3e 0x3d 0x3d 0x3e 0x3c ,
the write training result:
DQS0:0x35, DQS1:0x28, DQS2:0x2f, DQS3:0x22,
min :0x58 0x5c 0x5c 0x5b 0x51 0x54 0x53 0x53 0x56 ,0x4a 0x4a 0x43 0x44 0x4d 0x4d 0x4e 0x4c 0x4a ,
0x5c 0x5c 0x58 0x58 0x54 0x51 0x50 0x55 0x58 ,0x50 0x50 0x4d 0x4a 0x55 0x55 0x4e 0x54 0x4e ,
mid :0x73 0x76 0x77 0x75 0x6b 0x6d 0x6e 0x6e 0x71 ,0x65 0x65 0x5f 0x5f 0x68 0x68 0x69 0x67 0x66 ,
0x77 0x77 0x73 0x73 0x6d 0x69 0x6a 0x6f 0x72 ,0x6c 0x6a 0x68 0x64 0x6f 0x6f 0x6a 0x6e 0x6a ,
max :0x8e 0x90 0x92 0x90 0x86 0x86 0x8a 0x8a 0x8c ,0x81 0x80 0x7b 0x7a 0x84 0x83 0x84 0x83 0x82 ,
0x93 0x92 0x8e 0x8f 0x87 0x82 0x84 0x8a 0x8d ,0x89 0x84 0x84 0x7f 0x89 0x89 0x87 0x89 0x87 ,
range:0x36 0x34 0x36 0x35 0x35 0x32 0x37 0x37 0x36 ,0x37 0x36 0x38 0x36 0x37 0x36 0x36 0x37 0x38 ,
0x37 0x36 0x36 0x37 0x33 0x31 0x34 0x35 0x35 ,0x39 0x34 0x37 0x35 0x34 0x34 0x39 0x35 0x39 ,
CA Training result:
cs:0 min :0x47 0x42 0x3c 0x35 0x3d 0x36 0x3f ,0x44 0x3e 0x3c 0x34 0x39 0x32 0x3e ,
cs:0 mid :0x83 0x84 0x78 0x77 0x79 0x78 0x70 ,0x81 0x7f 0x78 0x76 0x76 0x74 0x6f ,
cs:0 max :0xbf 0xc6 0xb4 0xb9 0xb6 0xba 0xa1 ,0xbf 0xc1 0xb4 0xb8 0xb3 0xb7 0xa0 ,
cs:0 range:0x78 0x84 0x78 0x84 0x79 0x84 0x62 ,0x7b 0x83 0x78 0x84 0x7a 0x85 0x62 ,
cs:1 min :0x42 0x45 0x37 0x3a 0x39 0x3a 0x3b ,0x41 0x40 0x38 0x38 0x37 0x35 0x3b ,
cs:1 mid :0x82 0x83 0x78 0x77 0x79 0x78 0x6f ,0x81 0x7e 0x77 0x76 0x76 0x74 0x6f ,
cs:1 max :0xc3 0xc1 0xba 0xb5 0xba 0xb6 0xa4 ,0xc2 0xbd 0xb6 0xb5 0xb6 0xb4 0xa3 ,
cs:1 range:0x81 0x7c 0x83 0x7b 0x81 0x7c 0x69 ,0x81 0x7d 0x7e 0x7d 0x7f 0x7f 0x68 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-g606f72bd97a-240527 #lxh (May 30 2024 - 16:08:15), fwver: v1.14
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 (gzip @0x00240000) ... sha256(c25a9e81e4...) + sha256(b5946ac63d...) + OK
## Checking uboot 0x00a00000 (gzip @0x00c00000) ... sha256(dda8703b05...) + sha256(f800e1c7a3...) + OK
## Checking fdt 0x00b4e820 ... sha256(a474c6bb61...) + OK
## Checking atf-2 0xfdcc1000 ... sha256(b8dca786b4...) + OK
## Checking atf-3 0x0006b000 ... sha256(2f91089eb7...) + OK
## Checking atf-4 0xfdcce000 ... sha256(86ef885748...) + OK
## Checking atf-5 0xfdcd0000 ... sha256(0b2b146c60...) + OK
## Checking atf-6 0x00069000 ... sha256(a9a1e63bef...) + OK
## Checking optee 0x08400000 (gzip @0x08600000) ... sha256(6221fce17a...) + sha256(28fba8b7d7...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 167.932/336.479 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-645-g8cea6ab0b:cl, fwver: v1.44
NOTICE: BL31: Built : 16:36:43, Sep 19 2023
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid 220114
INFO: l3 cache partition cfg-0
INFO: dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-791-g185dc3c92 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Tue Apr 16 10:47:32 CST 2024 aarch64, fwver: v2.12
I/TC: OP-TEE memory: TEEOS 0x200000 TA 0xc00000 SHM 0x200000
I/TC: Primary CPU initializing
I/TC: CRYPTO_CRYPTO_VERSION_NEW no support. Skip all algo mode check.
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
usb dr_mode not found
usb dr_mode not found
U-Boot 2017.09 (Nov 01 2024 - 11:56:47 +0800)
Model: Rockchip RK3568 Evaluation Board
MPIDR: 0x0
PreSerial: 2, raw, 0xfe660000
DRAM: 4 GiB
Sysmem: init
Relocation Offset: ed211000
Relocation fdt: eb9f8508 - eb9fece8
CR: M/C/I
usb dr_mode not found
usb dr_mode not found
Using default environment
optee api revision: 2.0
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
MMC: no card present
mmc_init: -123, time 0
switch to partitions #0, OK
mmc0(part 0) is current device
Bootdev(scan): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
TEEC: Waring: Could not find security partition
DM: v1
boot mode: None
RESC: 'boot', blk@0x00019a95
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
usb dr_mode not found
usb dr_mode not found
I2c0 speed: 100000Hz
PMIC: RK8090 (on=0x40, off=0x00)
vdd_logic init 950000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
vsel-gpios- not found! Error: -2
vdd_cpu init 1000000 uV
io-domain: OK
INFO: ddr dmc_fsp already initialized in loader.
Could not find baseparameter partition
Model: pro-rk3566
Enable charge animation display
Exit charge: due to not enable uboot charge
Rockchip UBOOT DRM driver version: v1.0.1
Assign plane mask automatically
VOP have 2 active VP
vp0 have layer nr:3[1 3 5 ], primary plane: 5
vp1 have layer nr:3[0 2 4 ], primary plane: 4
vp2 have layer nr:0[], primary plane: 0
Using display timing dts
dsi@fe060000: detailed mode clock 51000 kHz, flags[a]
H: 1024 1160 1164 1324
V: 0600 0616 0618 0634
bus_format: 100e
VOP update mode to: 1024x600p61, type: MIPI0 for VP1
VP1 set crtc_clock to 51000KHz
Unsupported bt709f at 10bit csc depth, use bt601f instead
VOP VP1 enable Smart0[654x270->654x270@185x165] fmt[0] addr[0xedf00000]
final DSI-Link bandwidth: 480 Mbps x 4
xfer: num: 2, addr: 0x50
xfer: num: 2, addr: 0x50
Monitor has basic audio support
Could not find baseparameter partition
hdmi@fe0a0000: detailed mode clock 148500 kHz, flags[5]
H: 1920 2008 2052 2200
V: 1080 1084 1089 1125
bus_format: 2025
VOP update mode to: 1920x1080p60, type: HDMI0 for VP0
VP0 set crtc_clock to 148500KHz
VOP VP0 enable Smart1[654x270->654x270@633x405] fmt[0] addr[0xedf00000]
CEA mode used vic=16
final pixclk = 148500000 tmdsclk = 148500000
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
sink has audio support
hdmi_set_clk_regenerator: fs=48000Hz ftdms=148.500MHz N=6144 cts=148500
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 1104000 KHz
dpll 528000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 612000 KHz
hpll 148500 KHz
ppll 200000 KHz
armclk 1104000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 500000 KHz
aclk_top_low 400000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
Net: eth1: ethernet@fe010000
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "(none)"
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe94a4ac0 with size 0x02352a00
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e94a4ac0 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0xe94cf2c0
Data Size: 36864512 Bytes = 35.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00280000
Entry Point: 0x00280000
Hash algo: sha256
Hash value: f35f300057e8861d17532a75d31a265c39521245a749fb77e941e91704c00a75
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e94a4ac0 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xe94a52c0
Data Size: 171637 Bytes = 167.6 KiB
Architecture: AArch64
Load Address: 0x08300000
Hash algo: sha256
Hash value: f7d05bec7b0df3ef8859e186d264cd5ff9b39d6ba73af446478a282eb725456d
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x08300000 to 0x08300000
Booting using the fdt blob at 0x08300000
Loading Kernel Image from 0xe94cf2c0 to 0x00280000 ... OK
kernel loaded at 0x00280000, end = 0x025a8200
Using Device Tree in place at 0000000008300000, end 000000000832ce74
vp0, plane_mask:0x2a, primary-id:5, curser-id:-1
vp1, plane_mask:0x15, primary-id:4, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
## reserved-memory:
drm-logo@00000000: addr=edf00000 size=15a000
drm-cubic-lut@00000000: addr=eff00000 size=8000
ramoops@110000: addr=110000 size=f0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
board seed: Pseudo
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
== DO RELOCATE == Kernel from 0x00280000 to 0x00200000
Total: 1456.442/1504.614 ms
Starting kernel ...
[ 1.509796] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 1.509821] Linux version 5.10.209 (viewpro@viewpro-ThinkBook-16-G5-IRH) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Fri Nov 1 11:57:02 CST 2024
[ 1.511668] random: crng init done
[ 1.515794] Machine model: pro-rk3566
[ 1.550543] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ 1.555089] printk: bootconsole [uart8250] enabled
[ 1.556715] efi: UEFI not found.
[ 1.616410] Zone ranges:
[ 1.616664] DMA [mem 0x0000000000200000-0x00000000ffffffff]
[ 1.617253] DMA32 empty
[ 1.617528] Normal [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.618112] Movable zone start for each node
[ 1.618515] Early memory node ranges
[ 1.618854] node 0: [mem 0x0000000000200000-0x00000000083fffff]
[ 1.619446] node 0: [mem 0x0000000009400000-0x00000000efffffff]
[ 1.620039] node 0: [mem 0x00000001f0000000-0x00000001ffffffff]
[ 1.620632] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[ 1.640723] cma: Reserved 16 MiB at 0x00000000eec00000
[ 1.641296] psci: probing for conduit method from DT.
[ 1.641784] psci: PSCIv1.1 detected in firmware.
[ 1.642221] psci: Using standard PSCI v0.2 function IDs
[ 1.642718] psci: Trusted OS migration not required
[ 1.643181] psci: SMC Calling Convention v1.2
[ 1.643933] percpu: Embedded 30 pages/cpu s83800 r8192 d30888 u122880
[ 1.644650] Detected VIPT I-cache on CPU0
[ 1.645068] CPU features: detected: GIC system register CPU interface
[ 1.645676] CPU features: detected: Virtualization Host Extensions
[ 1.646263] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 1.646938] alternatives: patching kernel code
[ 1.649201] Built 1 zonelists, mobility grouping on. Total pages: 1027656
[ 1.649856] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 root=PARTUUID=614e0000-0000 androidboot.fwver=ddr-v1.21-2d653b3476,spl-v1.14,bl31-v1.44,bl32-v2.12,uboot-11/01/2024
[ 1.653735] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 1.654969] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 1.655701] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 1.672164] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[ 1.718644] Memory: 3974220K/4175872K available (18752K kernel code, 3488K rwdata, 6924K rodata, 6720K init, 592K bss, 185268K reserved, 16384K cma-reserved)
[ 1.720091] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 1.720742] ftrace: allocating 57287 entries in 224 pages
[ 1.794244] ftrace: allocated 224 pages with 3 groups
[ 1.795023] rcu: Hierarchical RCU implementation.
[ 1.795475] rcu: RCU event tracing is enabled.
[ 1.795904] rcu: RCU dyntick-idle grace-period acceleration is enabled.
[ 1.796535] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 1.797151] Rude variant of Tasks RCU enabled.
[ 1.797580] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 1.798291] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 1.803232] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 1.805412] GICv3: GIC: Using split EOI/Deactivate mode
[ 1.805917] GICv3: 320 SPIs implemented
[ 1.806281] GICv3: 0 Extended SPIs implemented
[ 1.806734] GICv3: Distributor has no Range Selector support
[ 1.807276] GICv3: 16 PPIs implemented
[ 1.808052] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 1.808821] ITS [mem 0xfd440000-0xfd45ffff]
[ 1.809289] ITS@0x00000000fd440000: allocated 8192 Devices @2810000 (indirect, esz 8, psz 64K, shr 0)
[ 1.810189] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @2820000 (flat, esz 2, psz 64K, shr 0)
[ 1.811152] ITS: using cache flushing for cmd queue
[ 1.811961] GICv3: using LPI property table @0x0000000002830000
[ 1.812633] GIC: using cache flushing for LPI property table
[ 1.813172] GICv3: CPU0: using allocated LPI pending table @0x0000000002840000
[ 1.813922] rcu: Offload RCU callbacks from CPUs: (none).
[ 1.842968] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 1.843559] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 1.844581] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 1.846416] Console: colour dummy device 80x25
[ 1.846882] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 1.847856] pid_max: default: 32768 minimum: 301
[ 1.848407] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.849119] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.851191] rcu: Hierarchical SRCU implementation.
[ 1.852294] Platform MSI: interrupt-controller@fd440000 domain created
[ 1.853376] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ 1.854568] EFI services will not be available.
[ 1.855279] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[ 1.856942] Detected VIPT I-cache on CPU1
[ 1.856971] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 1.856991] GICv3: CPU1: using allocated LPI pending table @0x0000000002850000
[ 1.857043] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 1.858312] Detected VIPT I-cache on CPU2
[ 1.858336] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 1.858352] GICv3: CPU2: using allocated LPI pending table @0x0000000002860000
[ 1.858388] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 1.859614] Detected VIPT I-cache on CPU3
[ 1.859636] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 1.859652] GICv3: CPU3: using allocated LPI pending table @0x0000000002870000
[ 1.859686] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 1.859781] smp: Brought up 1 node, 4 CPUs
[ 1.867193] SMP: Total of 4 processors activated.
[ 1.867647] CPU features: detected: Privileged Access Never
[ 1.868172] CPU features: detected: LSE atomic instructions
[ 1.868698] CPU features: detected: User Access Override
[ 1.869198] CPU features: detected: 32-bit EL0 Support
[ 1.869683] CPU features: detected: Common not Private translations
[ 1.870272] CPU features: detected: RAS Extension Support
[ 1.870781] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 1.871599] CPU features: detected: CRC32 instructions
[ 1.872084] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 1.872739] CPU features: detected: RCpc load-acquire (LDAPR)
[ 1.899748] CPU: All CPU(s) started at EL2
[ 1.901498] devtmpfs: initialized
[ 1.922136] Registered cp15_barrier emulation handler
[ 1.922632] Registered setend emulation handler
[ 1.923226] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 1.924156] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 1.925302] pinctrl core: initialized pinctrl subsystem
[ 1.926337] DMI not present or invalid.
[ 1.926955] NET: Registered protocol family 16
[ 1.928787] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 1.929592] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 1.932525] Registered FIQ tty driver
[ 1.933219] thermal_sys: Registered thermal governor 'fair_share'
[ 1.933225] thermal_sys: Registered thermal governor 'step_wise'
[ 1.933803] thermal_sys: Registered thermal governor 'user_space'
[ 1.934370] thermal_sys: Registered thermal governor 'power_allocator'
[ 1.935221] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 1.936664] cpuidle: using governor menu
[ 1.937296] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 1.938058] ASID allocator initialised with 65536 entries
[ 1.940764] ramoops: dmesg-0 0x20000@0x0000000000110000
[ 1.941283] ramoops: console 0x80000@0x0000000000130000
[ 1.941791] ramoops: pmsg 0x50000@0x00000000001b0000
[ 1.942614] printk: console [ramoops-1] enabled
[ 1.943062] pstore: Registered ramoops as persistent store backend
[ 1.943648] ramoops: using 0xf0000@0x110000, ecc: 0
[ 1.981342] rockchip-gpio fdd60000.gpio0: probed /pinctrl/gpio0@fdd60000
[ 1.982461] rockchip-gpio fe740000.gpio1: probed /pinctrl/gpio1@fe740000
[ 1.983578] rockchip-gpio fe750000.gpio2: probed /pinctrl/gpio2@fe750000
[ 1.984670] rockchip-gpio fe760000.gpio3: probed /pinctrl/gpio3@fe760000
[ 1.985764] rockchip-gpio fe770000.gpio4: probed /pinctrl/gpio4@fe770000
[ 1.986503] rockchip-pinctrl pinctrl: probed pinctrl
[ 2.007823] fiq_debugger fiq_debugger.0: IRQ fiq not found
[ 2.008362] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ 2.008913] fiq_debugger_probe: could not install nmi irq handler
拒绝访问。
Connection closed.
Disconnected from remote host(1M5UART21) at 09:38:49.
Type `help' to learn how to use Xshell prompt.
[C:\~]$
[END] 2024/11/2 9:38:56
115200bps波特率：
[BEGIN] 2024/11/2 9:40:08
2.036596] printk: console [ttyFIQ0] enabled
2.036596] printk: console [ttyFIQ0] enabled
[ 2.045745] printk: bootco[ 2.045745] printk: bootconsole [uart8250] disabled
nsole [uart8250] disabled
[ 2.056154] Registered fiq debugger ttyFIQ0
[ 2.056849] vcc3v3_sys: supplied by dc_12v
[ 2.057094] vcc5v0_sys: supplied by dc_12v
[ 2.057369] vcc3v3_lcd0_n: supplied by vcc3v3_sys
[ 2.057612] vcc3v3_lcd1_n: supplied by vcc3v3_sys
[ 2.058708] iommu: Default domain type: Translated
[ 2.061999] SCSI subsystem initialized
[ 2.062217] usbcore: registered new interface driver usbfs
[ 2.062262] usbcore: registered new interface driver hub
[ 2.062301] usbcore: registered new device driver usb
[ 2.062388] mc: Linux media interface: v0.10
[ 2.062421] videodev: Linux video capture interface: v2.00
[ 2.062495] pps_core: LinuxPPS API ver. 1 registered
[ 2.062504] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.062521] PTP clock support registered
[ 2.062561] EDAC MC: Ver: 3.0.0
[ 2.063490] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 2.063556] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 2.065384] Advanced Linux Sound Architecture Driver Initialized.
[ 2.065793] Bluetooth: Core ver 2.22
[ 2.065830] NET: Registered protocol family 31
[ 2.065839] Bluetooth: HCI device and connection manager initialized
[ 2.065852] Bluetooth: HCI socket layer initialized
[ 2.065862] Bluetooth: L2CAP socket layer initialized
[ 2.065881] Bluetooth: SCO socket layer initialized
[ 2.066325] rockchip-cpuinfo cpuinfo: SoC : 35662000
[ 2.066338] rockchip-cpuinfo cpuinfo: Serial : 35e261fa0f931014
[ 2.067040] clocksource: Switched to clocksource arch_sys_counter
[ 2.489419] NET: Registered protocol family 2
[ 2.489654] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 2.491297] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 2.491390] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 2.491557] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ 2.491952] TCP: Hash tables configured (established 32768 bind 32768)
[ 2.492060] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 2.492111] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 2.492271] NET: Registered protocol family 1
[ 2.492708] RPC: Registered named UNIX socket transport module.
[ 2.492718] RPC: Registered udp transport module.
[ 2.492724] RPC: Registered tcp transport module.
[ 2.492731] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.493659] PCI: CLS 0 bytes, default 64
[ 2.496341] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ 2.497347] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[ 2.501363] Initialise system trusted keyrings
[ 2.501509] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[ 2.505529] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.506062] NFS: Registering the id_resolver key type
[ 2.506091] Key type id_resolver registered
[ 2.506099] Key type id_legacy registered
[ 2.506138] ntfs: driver 2.1.32 [Flags: R/O].
[ 2.506328] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 2.506579] fuse: init (API version 7.32)
[ 2.506866] SGI XFS with security attributes, no debug enabled
[ 2.538323] NET: Registered protocol family 38
[ 2.538348] Key type asymmetric registered
[ 2.538357] Asymmetric key parser 'x509' registered
[ 2.538399] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 2.538409] io scheduler mq-deadline registered
[ 2.538417] io scheduler kyber registered
[ 2.539116] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[ 2.539894] rockchip-csi2-dphy csi2-dphy1: csi2 dphy1 probe successfully!
[ 2.549669] pwm-backlight backlight: supply power not found, using dummy regulator
[ 2.550227] iep: Module initialized.
[ 2.550292] mpp_service mpp-srv: unknown mpp version for missing VCS info
[ 2.550303] mpp_service mpp-srv: probe start
[ 2.552090] mpp_vdpu2 fdea0400.vdpu: Adding to iommu group 1
[ 2.552290] mpp_vdpu2 fdea0400.vdpu: probe device
[ 2.552571] mpp_vdpu2 fdea0400.vdpu: probing finish
[ 2.552992] mpp_vepu2 fdee0000.vepu: Adding to iommu group 3
[ 2.553154] mpp_vepu2 fdee0000.vepu: probing start
[ 2.553388] mpp_vepu2 fdee0000.vepu: probing finish
[ 2.553858] mpp-iep2 fdef0000.iep: Adding to iommu group 4
[ 2.554014] mpp-iep2 fdef0000.iep: probe device
[ 2.554258] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[ 2.554293] mpp-iep2 fdef0000.iep: probing finish
[ 2.554671] mpp_jpgdec fded0000.jpegd: Adding to iommu group 2
[ 2.554819] mpp_jpgdec fded0000.jpegd: probe device
[ 2.555078] mpp_jpgdec fded0000.jpegd: probing finish
[ 2.556261] mpp_service mpp-srv: probe success
[ 2.560552] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[ 2.560576] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 2.562268] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[ 2.562284] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 2.563036] rockchip-pvtm fde00000.pvtm: pvtm@0 probed
[ 2.563172] rockchip-pvtm fde80000.pvtm: pvtm@1 probed
[ 2.563277] rockchip-pvtm fde90000.pvtm: pvtm@2 probed
[ 2.563962] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 2.564591] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[ 2.564851] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 2.565846] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 71, base_baud = 1500000) is a 16550A
[ 2.566412] fe670000.serial: ttyS3 at MMIO 0xfe670000 (irq = 72, base_baud = 1500000) is a 16550A
[ 2.566947] fe6a0000.serial: ttyS6 at MMIO 0xfe6a0000 (irq = 73, base_baud = 1500000) is a 16550A
[ 2.567459] fe6b0000.serial: ttyS7 at MMIO 0xfe6b0000 (irq = 74, base_baud = 1500000) is a 16550A
[ 2.568117] fe6d0000.serial: ttyS9 at MMIO 0xfe6d0000 (irq = 75, base_baud = 1500000) is a 16550A
[ 2.571128] rockchip-vop2 fe040000.vop: Adding to iommu group 8
[ 2.579664] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x2a, primary plane phy id: 5
[ 2.579693] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x15, primary plane phy id: 4
[ 2.579704] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 2.579883] rockchip-vop2 fe040000.vop: [drm:vop2_bind] VP2 plane_mask is zero, so ignore register crtc
[ 2.579976] [drm] failed to init overlay plane Cluster0-win1
[ 2.580020] [drm] failed to init overlay plane Cluster1-win1
[ 2.580152] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffffc00935f950)
[ 2.580493] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 2.581047] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 2.581271] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found
[ 2.581632] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffffc00936e4d8)
[ 2.581728] dw-mipi-dsi-rockchip fe060000.dsi: failed to find panel or bridge: -517
[ 2.588656] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 2.589327] brd: module loaded
[ 2.593871] loop: module loaded
[ 2.594219] zram: Added device: zram0
[ 2.594453] lkdtm: No crash points registered, enable through debugfs
[ 2.595355] system_heap: orders[0] = 6
[ 2.595369] system_heap: orders[1] = 4
[ 2.595376] system_heap: orders[2] = 0
[ 2.596967] ahci fc800000.sata: supply ahci not found, using dummy regulator
[ 2.597122] ahci fc800000.sata: supply phy not found, using dummy regulator
[ 2.597364] ahci fc800000.sata: supply target not found, using dummy regulator
[ 2.597491] ahci fc800000.sata: forcing port_map 0x0 -> 0x1
[ 2.597535] ahci fc800000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 2.597547] ahci fc800000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst
[ 2.597566] ahci fc800000.sata: port 0 is not capable of FBS
[ 2.598476] scsi host0: ahci
[ 2.598743] ata1: SATA max UDMA/133 mmio [mem 0xfc800000-0xfc800fff] port 0x100 irq 19
[ 2.601486] rockchip-spi fe620000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ 2.602912] rockchip-spi fe630000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ 2.604305] rockchip-spi fe640000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ 2.607661] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[ 2.607877] rk_gmac-dwmac fe010000.ethernet: supply phy not found, using dummy regulator
[ 2.608021] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[ 2.608034] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3a).
[ 2.608045] rk_gmac-dwmac fe010000.ethernet: RX delay(0x29).
[ 2.608059] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 2.608093] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[ 2.608334] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 2.608544] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 2.608557] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 2.608568] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ 2.608577] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ 2.608584] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 2.608591] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 2.608649] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 2.608659] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.608667] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 2.608676] rk_gmac-dwmac fe010000.ethernet: Using 32 bits DMA width
[ 2.743123] usbcore: registered new interface driver rtl8150
[ 2.743182] usbcore: registered new interface driver r8152
[ 2.754678] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.754710] ehci-pci: EHCI PCI platform driver
[ 2.754786] ehci-platform: EHCI generic platform driver
[ 2.755182] phy phy-fe8b0000.usb2-phy.4: illegal mode
[ 2.757223] ehci-platform fd800000.usb: EHCI Host Controller
[ 2.757385] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 2.757513] ehci-platform fd800000.usb: irq 20, io mem 0xfd800000
[ 2.770391] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 2.770563] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.770575] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.770584] usb usb1: Product: EHCI Host Controller
[ 2.770591] usb usb1: Manufacturer: Linux 5.10.209 ehci_hcd
[ 2.770599] usb usb1: SerialNumber: fd800000.usb
[ 2.770994] hub 1-0:1.0: USB hub found
[ 2.771033] hub 1-0:1.0: 1 port detected
[ 2.773681] ehci-platform fd880000.usb: EHCI Host Controller
[ 2.773875] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ 2.773992] ehci-platform fd880000.usb: irq 22, io mem 0xfd880000
[ 2.787061] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 2.787212] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.787225] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.787233] usb usb2: Product: EHCI Host Controller
[ 2.787241] usb usb2: Manufacturer: Linux 5.10.209 ehci_hcd
[ 2.787248] usb usb2: SerialNumber: fd880000.usb
[ 2.787686] hub 2-0:1.0: USB hub found
[ 2.787724] hub 2-0:1.0: 1 port detected
[ 2.788405] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.788442] ohci-platform: OHCI generic platform driver
[ 2.788754] phy phy-fe8b0000.usb2-phy.4: illegal mode
[ 2.788768] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 2.788921] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ 2.789043] ohci-platform fd840000.usb: irq 21, io mem 0xfd840000
[ 2.847845] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 2.847858] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.847867] usb usb3: Product: Generic Platform OHCI controller
[ 2.847875] usb usb3: Manufacturer: Linux 5.10.209 ohci_hcd
[ 2.847882] usb usb3: SerialNumber: fd840000.usb
[ 2.848268] hub 3-0:1.0: USB hub found
[ 2.848304] hub 3-0:1.0: 1 port detected
[ 2.848790] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 2.848938] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 2.849039] ohci-platform fd8c0000.usb: irq 23, io mem 0xfd8c0000
[ 2.907853] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 2.907866] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.907876] usb usb4: Product: Generic Platform OHCI controller
[ 2.907884] usb usb4: Manufacturer: Linux 5.10.209 ohci_hcd
[ 2.907891] usb usb4: SerialNumber: fd8c0000.usb
[ 2.908269] hub 4-0:1.0: USB hub found
[ 2.908308] hub 4-0:1.0: 1 port detected
[ 2.909547] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.909710] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5
[ 2.909841] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 2.909897] xhci-hcd xhci-hcd.0.auto: irq 89, io mem 0xfd000000
[ 2.910021] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.910090] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.910175] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6
[ 2.910199] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 2.910332] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.910344] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.910353] usb usb5: Product: xHCI Host Controller
[ 2.910397] usb usb5: Manufacturer: Linux 5.10.209 xhci-hcd
[ 2.910407] usb usb5: SerialNumber: xhci-hcd.0.auto
[ 2.910807] hub 5-0:1.0: USB hub found
[ 2.910844] hub 5-0:1.0: 1 port detected
[ 2.911159] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.911250] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 2.911262] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.911271] usb usb6: Product: xHCI Host Controller
[ 2.911279] usb usb6: Manufacturer: Linux 5.10.209 xhci-hcd
[ 2.911286] usb usb6: SerialNumber: xhci-hcd.0.auto
[ 2.911637] hub 6-0:1.0: USB hub found
[ 2.911671] hub 6-0:1.0: 1 port detected
[ 2.912065] usbcore: registered new interface driver cdc_acm
[ 2.912075] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.912293] usbcore: registered new interface driver uas
[ 2.912381] usbcore: registered new interface driver usb-storage
[ 2.912472] usbcore: registered new interface driver usbserial_generic
[ 2.912497] usbserial: USB Serial support registered for generic
[ 2.912538] usbcore: registered new interface driver cp210x
[ 2.912560] usbserial: USB Serial support registered for cp210x
[ 2.912616] usbcore: registered new interface driver ftdi_sio
[ 2.912641] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.912763] usbcore: registered new interface driver keyspan
[ 2.912787] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 2.912807] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 2.912827] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 2.912851] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 2.912895] usbcore: registered new interface driver option
[ 2.912918] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.913067] usbcore: registered new interface driver oti6858
[ 2.913089] usbserial: USB Serial support registered for oti6858
[ 2.913134] usbcore: registered new interface driver pl2303
[ 2.913156] usbserial: USB Serial support registered for pl2303
[ 2.913202] usbcore: registered new interface driver qcserial
[ 2.913225] usbserial: USB Serial support registered for Qualcomm USB modem
[ 2.913276] usbcore: registered new interface driver sierra
[ 2.913299] usbserial: USB Serial support registered for Sierra USB modem
[ 2.914565] usbcore: registered new interface driver usbtouchscreen
[ 2.915182] i2c /dev entries driver
[ 2.918110] rk808 0-0020: chip id: 0x8090
[ 2.918164] rk808 0-0020: No cache defaults, reading back from HW
[ 2.941853] rk808 0-0020: source: on=0x10, off=0x00
[ 2.941872] rk808 0-0020: support dcdc3 fb mode:-22, 1
[ 2.941883] rk808 0-0020: support pmic reset mode:0,0
[ 2.946904] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 2.946938] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 2.947365] vdd_logic: supplied by vcc3v3_sys
[ 2.948346] vdd_gpu: supplied by vcc3v3_sys
[ 2.948925] vcc_ddr: supplied by vcc3v3_sys
[ 2.949493] vdd_npu: supplied by vcc3v3_sys
[ 2.950412] vcc_1v8: supplied by vcc3v3_sys
[ 2.950977] vdda0v9_image: supplied by vcc3v3_sys
[ 2.952383] vdda_0v9: supplied by vcc3v3_sys
[ 2.953457] vdda0v9_pmu: supplied by vcc3v3_sys
[ 2.954539] vccio_acodec: supplied by vcc3v3_sys
[ 2.955946] vccio_sd: supplied by vcc3v3_sys
[ 2.957061] vcc3v3_pmu: supplied by vcc3v3_sys
[ 2.958480] vcca_1v8: supplied by vcc3v3_sys
[ 2.959557] vcca1v8_pmu: supplied by vcc3v3_sys
[ 2.960645] vcca1v8_image: supplied by vcc3v3_sys
[ 2.962047] vcc_3v3: supplied by vcc3v3_sys
[ 2.962944] vcc3v3_sd: supplied by vcc3v3_sys
[ 2.964387] rk817-battery rk817-battery: DMA mask not set
[ 2.964523] rk817-battery rk817-battery: fb_temperature missing!
[ 2.964537] rk817-battery rk817-battery: zero_reserve_dsoc missing!
[ 2.964548] rk817-battery rk817-battery: low_power_sleep missing!
[ 2.964558] rk817-battery rk817-battery: battery design_max_voltage missing!
[ 2.987878] rk817-bat: initialized yet..
[ 3.033993] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[ 3.037066] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 3.037583] rk817-charger: Failed to locate of_node [id: -1]
Start mounting all internal partitions in /etc/fstab
[ 3.037735] rk817-charger rk817-charger: Failed to find matching dt id
Log saved to /var/log/mount-all.log
[ 3.040845] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
Note: Will skip fsck, remove /.skip_fsck to enable
[ 3.046675] rk808-rtc rk808-rtc: registered as rtc0
[ 3.048434] rk808-rtc rk808-rtc: setting system clock to 2017-08-04T09:00:44 UTC (1501837244)
[ 3.049907] fan53555-regulator 0-001c: Failed to get chip ID!
[ 3.055899] rtc-hym8563 4-0051: rtc information is valid
[0]: Handling /dev/mmcblk0p6 / ext4 rw,noauto 1
[ 3.061212] rtc-hym8563 4-0051: registered as rtc1
[ 3.064829] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: enter mipi csi2 hw probe!
[1]: Handling /dev/mmcblk0p7 /oem ext4 defaults 2
[ 3.064992] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: probe success, v4l2_dev:mipi-csi2-hw!
[2]: Handling /dev/mmcblk0p8 /userdata ext4 defaults 2
[ 3.066436] rkisp_hw fdff0000.rkisp: Adding to iommu group 7
[ 3.066662] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
[ 3.066692] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[ 3.066720] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
[ 3.066876] rkisp_hw fdff0000.rkisp: no find phandle sram
[2]: Already resized /dev/mmcblk0p8(ext4)
[ 3.067391] rkisp rkisp-vir0: rkisp driver version: v02.05.01
[0]: Already resized /dev/mmcblk0p6(ext4)
[ 3.067548] rkisp rkisp-vir0: No memory-region-thunderboot specified
[1]: Already resized /dev/mmcblk0p7(ext4)
[ 3.067780] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
Starting syslogd: [ 3.067804] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
OK
[ 3.070439] usbcore: registered new interface driver uvcvideo
log-guardian: [WARN] Not a dir: "/var/log/,/tmp/"
[ 3.070459] USB Video Class driver (1.1.1)
Starting klogd: log-guardian: Guarding logs in: "/var/log/,/tmp/"...
[ 3.072086] Bluetooth: HCI UART driver ver 2.3
OK
[ 3.072107] Bluetooth: HCI UART protocol H4 registered
Running sysctl: OK
[ 3.072114] Bluetooth: HCI UART protocol ATH3K registered
[ 3.072180] usbcore: registered new interface driver bfusb
[ 3.072228] usbcore: registered new interface driver btusb
Populating /dev using udev: [ 3.073075] cpu cpu0: bin=0
[ 3.073141] cpu cpu0: leakage=24
[ 3.073184] cpu cpu0: pvtm = 88110, from nvmem
[ 3.073200] cpu cpu0: pvtm-volt-sel=2
[ 3.073256] cpu cpu0: soc version=0, speed=2
[ 3.075432] sdhci: Secure Digital Host Controller Interface driver
[ 3.075450] sdhci: Copyright(c) Pierre Ossman
[ 3.075465] Synopsys Designware Multimedia Card Interface Driver
[ 3.076222] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.076756] dwmmc_rockchip fe000000.dwmmc: No normal pinctrl state
[ 3.076774] dwmmc_rockchip fe000000.dwmmc: No idle pinctrl state
[ 3.076835] dwmmc_rockchip fe2b0000.dwmmc: No normal pinctrl state
[ 3.076850] dwmmc_rockchip fe2b0000.dwmmc: No idle pinctrl state
[ 3.076900] dwmmc_rockchip fe000000.dwmmc: IDMAC supports 32-bit address mode.
[ 3.076931] dwmmc_rockchip fe000000.dwmmc: Using internal DMA controller.
[ 3.076943] dwmmc_rockchip fe000000.dwmmc: Version ID is 270a
[ 3.076968] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ 3.076994] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ 3.077002] dwmmc_rockchip fe000000.dwmmc: DW MMC controller at irq 53,32 bit host data width,256 deep fifo
[ 3.077015] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ 3.077082] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 54,32 bit host data width,256 deep fifo
[ 3.077437] dwmmc_rockchip fe000000.dwmmc: allocated mmc-pwrseq
[ 3.077455] mmc_host mmc3: card is non-removable.
[ 3.077841] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ 3.077927] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 3.078850] cryptodev: driver 1.12 loaded.
[ 3.078913] hid: raw HID events driver (C) Jiri Kosina
[ 3.079230] usbcore: registered new interface driver usbhid
[ 3.079241] usbhid: USB HID core driver
[ 3.084956] usbcore: registered new interface driver snd-usb-audio
[ 3.087255] rk817-codec rk817-codec: DMA mask not set
[ 3.090641] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 3.091554] rockchip-i2s-tdm fe410000.i2s: Register PCM for TRCM mode
[ 3.094498] rk-multicodecs rk809-sound: Failed to get ADC channel
[ 3.094634] rk-multicodecs rk809-sound: ASoC: Property 'rockchip,audio-routing' does not exist or its length is not even
[ 3.095887] rk817-codec rk817-codec: rk817_probe: chip_name:0x80, chip_ver:0x95
[ 3.100513] rk-multicodecs rk809-sound: Don't need to map headset detect gpio to irq
[ 3.103972] Initializing XFRM netlink socket
[ 3.104403] NET: Registered protocol family 10
[ 3.105281] Segment Routing with IPv6
[ 3.105345] NET: Registered protocol family 17
[ 3.105369] NET: Registered protocol family 15
[ 3.105601] Bluetooth: RFCOMM socket layer initialized
[ 3.105636] Bluetooth: RFCOMM ver 1.11
[ 3.105660] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.105673] Bluetooth: HIDP socket layer initialized
[ 3.105715] [BT_RFKILL]: Enter rfkill_rk_init
[ 3.105723] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 3.106427] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 3.106479] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6398s
[ 3.106488] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 3.106495] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 3.106529] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 124, flags = 0.
[ 3.106542] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 3.106548] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 3.106556] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 3.106563] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 3.107169] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ 3.107581] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 142.
[ 3.107612] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 133.
[ 3.107626] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 134.
[ 3.107639] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 137.
[ 3.107705] [BT_RFKILL]: Request irq for bt wakeup host
[ 3.108125] [BT_RFKILL]: ** disable irq
[ 3.108232] [BT_RFKILL]: bt_default device registered.
[ 3.108346] input: bt-powerkey as /devices/platform/wireless-bluetooth/input/input1
[ 3.108683] Key type dns_resolver registered
[ 3.110460] Loading compiled-in X.509 certificates
[ 3.111550] pstore: Using crash dump compression: deflate
[ 3.112951] rga2 fdeb0000.rk_rga: probe successfully, irq = 31, hw_version:3.2.63318
[ 3.113337] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
[ 3.113598] rga: Module initialized. v1.3.3
[ 3.150118] mmc0: Host Software Queue enabled
[ 3.150158] mmc0: new HS200 MMC card at address 0001
[ 3.150857] mmcblk0: mmc0:0001 SPeMMC 29.0 GiB
[ 3.151066] mmcblk0boot0: mmc0:0001 SPeMMC partition 1 4.00 MiB
[ 3.151279] mmcblk0boot1: mmc0:0001 SPeMMC partition 2 4.00 MiB
[ 3.151612] mmcblk0rpmb: mmc0:0001 SPeMMC partition 3 4.00 MiB, chardev (236:0)
[ 3.155073] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
done
[ 3.186007] usb 2-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=61.60
[ 3.186034] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
Starting irqbalance: [ 3.186042] usb 2-1: Product: USB2.0 Hub
[ 3.187004] hub 2-1:1.0: USB hub found
[ 3.187495] hub 2-1:1.0: 4 ports detected
[ 3.216397] vendor storage:20190527 ret = 0
[ 3.294080] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
OK
[ 3.306801] mpp_rkvenc fdf40000.rkvenc: Adding to iommu group 5
[ 3.307097] mpp_rkvenc fdf40000.rkvenc: probing start
[ 3.307599] mpp_rkvenc fdf40000.rkvenc: bin=0
[ 3.307627] mpp_rkvenc fdf40000.rkvenc: Failed to get leakage
[ 3.307681] mpp_rkvenc fdf40000.rkvenc: pvtm = 88110, from nvmem
[ 3.307695] mpp_rkvenc fdf40000.rkvenc: pvtm-volt-sel=1
[ 3.307888] mpp_rkvenc fdf40000.rkvenc: avs=0
[ 3.308015] mpp_rkvenc fdf40000.rkvenc: failed to find power_model node
Initializing random number generator: OK
[ 3.308027] mpp_rkvenc fdf40000.rkvenc: failed to initialize power model
Saving random seed: [ 3.308035] mpp_rkvenc fdf40000.rkvenc: failed to get dynamic-coefficient
OK
[ 3.308461] mpp_rkvenc fdf40000.rkvenc: probing finish
[ 3.308865] mpp_rkvdec2 fdf80200.rkvdec: Adding to iommu group 6
[ 3.309083] mpp_rkvdec2 fdf80200.rkvdec: rkvdec, probing start
[ 3.309400] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
Starting system message bus: [ 3.309412] rkvdec2_init:1024: No niu aclk reset resource define
[ 3.309422] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[ 3.309429] rkvdec2_init:1027: No niu hclk reset resource define
[ 3.309643] mpp_rkvdec2 fdf80200.rkvdec: bin=0
[ 3.309749] mpp_rkvdec2 fdf80200.rkvdec: leakage=46
done
[ 3.309764] mpp_rkvdec2 fdf80200.rkvdec: leakage-volt-sel=0
[ 3.309803] mpp_rkvdec2 fdf80200.rkvdec: pvtm = 88110, from nvmem
[ 3.309816] mpp_rkvdec2 fdf80200.rkvdec: pvtm-volt-sel=1
[ 3.309997] mpp_rkvdec2 fdf80200.rkvdec: avs=0
[ 3.310119] mpp_rkvdec2 fdf80200.rkvdec: failed to find power_model node
Starting bluetoothd: OK
[ 3.310131] mpp_rkvdec2 fdf80200.rkvdec: failed to initialize power model
[ 3.310140] mpp_rkvdec2 fdf80200.rkvdec: failed to get dynamic-coefficient
[ 3.310264] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
Starting network: [ 3.310275] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[ 3.310283] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[ 3.310290] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[ 3.310299] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[ 3.310355] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[ 3.310468] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ 3.311685] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc3v3_pmu
[ 3.311702] mali fde60000.gpu: Kernel DDK version g21p0-01eac0
[ 3.311789] mali fde60000.gpu: GPU metrics tracepoint support enabled
[ 3.311867] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3000000 uV) supplied by vccio_acodec
[ 3.312012] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vccio_sd
[ 3.312140] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(3300000 uV) supplied by vcc_3v3
[ 3.312181] mali fde60000.gpu: bin=0
OK
[ 3.312201] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 3.312234] mali fde60000.gpu: leakage=6
[ 3.312275] mali fde60000.gpu: pvtm = 88110, from nvmem
[ 3.312293] mali fde60000.gpu: pvtm-volt-sel=2
Starting dhcpcd...
[ 3.312323] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc_1v8
[ 3.312342] mali fde60000.gpu: soc version=0, speed=2
dhcpcd-10.0.4 starting
[ 3.312403] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
dev: loaded udev
[ 3.312938] mali fde60000.gpu: avs=0
DUID 00:01:00:01:21:16:f4:3b:70:f7:54:9a:5f:9a
[ 3.312963] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 3.313406] mali fde60000.gpu: Register LUT 00070200 initialized for GPU arch 0x00070400
[ 3.313443] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 3.313627] mali fde60000.gpu: No priority control manager is configured
[ 3.313640] mali fde60000.gpu: Large page allocation set to false after hardware feature check
[ 3.314060] mali fde60000.gpu: No memory group manager is configured
[ 3.315611] mali fde60000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 3.317000] mali fde60000.gpu: Probed as mali0
[ 3.317384] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x2a, primary plane phy id: 5
[ 3.317407] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x15, primary plane phy id: 4
forked to background, child pid 495
[ 3.317419] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
dhcpcd_fork_cb: truncated read 0 (expected 4)
[ 3.317602] rockchip-vop2 fe040000.vop: [drm:vop2_bind] VP2 plane_mask is zero, so ignore register crtc
Starting chrony: [ 3.317695] [drm] failed to init overlay plane Cluster0-win1
OK
[ 3.317738] [drm] failed to init overlay plane Cluster1-win1
[ 3.317869] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffffc00935f950)
starting weston... done.
[ 3.318158] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 3.319322] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
Starting dropbear sshd: [ 3.320020] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found
[ 3.321071] input: hdmi_cec_key as /devices/platform/fe0a0000.hdmi/dw-hdmi-cec.4.auto/input/input2
OK
[ 3.321958] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffffc00936e4d8)
[ 3.322100] rockchip-drm display-subsystem: bound fe060000.dsi (ops 0xffffffc00936feb0)
Starting pulseaudio: OK
[ 3.340623] mmc3: queuing unknown CIS tuple 0x80 (2 bytes)
[ 3.342712] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[ 3.344617] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[ 3.348146] mmc3: queuing unknown CIS tuple 0x80 (7 bytes)
Starting dnsmasq: [ 3.352576] mmc3: queuing unknown CIS tuple 0x81 (9 bytes)
[ 3.434519] mmc_host mmc3: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[ 3.453861] dwmmc_rockchip fe000000.dwmmc: Successfully tuned phase to 270
[ 3.459966] mmc3: new ultra high speed SDR104 SDIO card at address 0001
[ 3.577784] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
[ 3.578737] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[ 3.579342] input: adc-keys as /devices/platform/adc-keys/input/input3
[ 3.586094] rockchip_headset rk-headset: Can not read property hook_gpio
OK
[ 3.586125] rockchip_headset rk-headset: have not set adc chan
[ 3.586136] rockchip_headset rk-headset: headset have no hook mode
[ 3.586344] input: rk-headset as /devices/platform/rk-headset/input/input4
[ 3.587188] RKNPU fde40000.npu: Adding to iommu group 0
W: [pulseaudio] main.c: This program is not intended to be run as root (unless --system is specified).
[ 3.587730] RKNPU fde40000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
W: [pulseaudio] main.c: Compiled with DEPRECATED libsamplerate support!
[ 3.588010] RKNPU fde40000.npu: can't request region for resource [mem 0xfde40000-0xfde4ffff]
/bin/list-iodomain.sh version: V1.0.1
[ 3.588605] [drm] Initialized rknpu 0.9.6 20240322 for fde40000.npu on minor 1
[ 3.589179] RKNPU fde40000.npu: bin=0
[ 3.589232] RKNPU fde40000.npu: leakage=3
[ 3.589273] RKNPU fde40000.npu: pvtm = 88110, from nvmem
[ 3.589291] RKNPU fde40000.npu: pvtm-volt-sel=2
[ 3.589307] RKNPU fde40000.npu: soc version=0, speed=2
[ 3.589901] RKNPU fde40000.npu: avs=0
[ 3.590083] RKNPU fde40000.npu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
fstrim: Starting fstrim process (638)...
[ 3.590618] RKNPU fde40000.npu: failed to find power_model node
[ 3.590633] RKNPU fde40000.npu: RKNPU: failed to initialize power model
Starting input-event-daemon: [ 3.590641] RKNPU fde40000.npu: RKNPU: failed to get dynamic-coefficient
Get CHIP ID: rk356x
[ 3.591709] cfg80211: Loading compiled-in X.509 certificates for regulatory database
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
[ 3.593533] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
XXXXXXXXXX PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!!
[ 3.594261] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
XXXXXXXXXX 请务必检查IO电源域配置 !!!!!!!!!!!!!!!
[ 3.595209] rockchip-pm rockchip-suspend: not set pwm-regulator-config
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
[ 3.595767] rockchip-suspend not set sleep-mode-config for mem-lite
Get IO DOMAIN VALUE:
[ 3.595776] rockchip-suspend not set wakeup-config for mem-lite
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
[ 3.595785] rockchip-suspend not set sleep-mode-config for mem-ultra
注意事项：PMUIO1/PMUIO2 固定不可配
[ 3.595791] rockchip-suspend not set wakeup-config for mem-ultra
VCCIO2电平由硬件FLASH_VOL_SEL决定:
[ 3.596937] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '11:59:03', on 'Nov 1 2024'.
当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平;
[ 3.597438] Mali:
当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平;
[ 3.597442] Mali device driver loaded
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
[ 3.597466] rkisp rkisp-vir0: clear unready subdev num: 1
done
[ 3.597686] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
pmuio2_vsel: 3.3V
[ 3.597700] cfg80211: failed to load regulatory.db
vccio7_vsel: 3.3V
[ 3.598041] rkisp-vir0: update sensor failed
vccio6_vsel: 1.8V
[ 3.598068] ALSA device list:
vccio5_vsel: 3.3V
[ 3.598078] #0: rockchip-rk809
vccio4_vsel: 3.3V
[ 3.598085] #1: rockchip,hdmi
vccio3_vsel: 3.3V
[ 3.656764] EXT4-fs (mmcblk0p6): recovery complete
vccio2_vsel: 3.3V
[ 3.656912] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
vccio1_vsel: 3.3V
[ 3.656981] VFS: Mounted root (ext4 filesystem) on device 179:6.
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
[ 3.657870] devtmpfs: mounted
root@rk3566-buildroot:/# Date: 2017-08-04 UTC
[ 3.663702] Freeing unused kernel memory: 6720K
[09:00:46.957] weston 13.0.1
[ 3.663893] Run /sbin/init as init process
https://wayland.freedesktop.org
[ 3.731697] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/
[ 3.902683] EXT4-fs (mmcblk0p7): recovery complete
Build: 13.0.1
[ 3.902830] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
[09:00:46.959] Command line: /usr/bin/weston
[ 3.902867] ext4 filesystem being mounted at /oem supports timestamps until 2038 (0x7fffffff)
[09:00:46.959] OS: Linux, 5.10.209, #1 SMP Fri Nov 1 11:57:02 CST 2024, aarch64
[ 3.905675] EXT4-fs (mmcblk0p8): warning: mounting unchecked fs, running e2fsck is recommended
[09:00:46.959] Flight recorder: enabled
[ 3.906461] EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts: (null)
[09:00:46.959] warning: XDG_RUNTIME_DIR "/var/run" is not configured
[ 3.906494] ext4 filesystem being mounted at /userdata supports timestamps until 2038 (0x7fffffff)
correctly. Unix access mode must be 0700 (current mode is 0755),
[ 4.110445] ---headsetobserve_work---
and must be owned by the user UID 0 (current owner is UID 0).
[ 4.201266] udevd[331]: starting version 3.2.10
Refer to your distribution on how to get it, or
[ 4.217191] old_status == headset_info->headset_status
http://www.freedesktop.org/wiki/Specifications/basedir-spec
[ 4.220654] udevd[332]: starting eudev-3.2.10
on how to implement it.
[09:00:46.968] Using config file '/etc/xdg/weston/weston.ini'
[09:00:46.971] Output repaint window is -1 ms maximum.
[09:00:46.974] Loading module '/usr/lib/libweston-13/drm-backend.so'
[09:00:46.981] initializing drm backend
[09:00:46.981] Entering mirror mode.
[09:00:46.981] Trying direct launcher...
[09:00:46.984] using /dev/dri/card0
[09:00:46.984] DRM: does not support atomic modesetting
[09:00:46.984] DRM: does not support GBM modifiers
[09:00:46.984] DRM: does not support async page flipping
[09:00:46.984] DRM: supports picture aspect ratio
[09:00:46.992] Loading module '/usr/lib/libweston-13/gl-renderer.so'
[09:00:47.035] EGL version: 1.4 Bifrost-"g13p0-01eac0"
[09:00:47.035] EGL vendor: ARM
[09:00:47.036] EGL client APIs: OpenGL_ES
[09:00:47.036] EGL features:
EGL Wayland extension: yes
context priority: yes
buffer age: no
partial update: yes
swap buffers with damage: no
configless context: yes
surfaceless context: yes
dmabuf support: modifiers
[09:00:47.063] GL version: OpenGL ES 3.2 v1.g13p0-01eac0.98c5dad4e3309b873e3189000b74ea36
[09:00:47.063] GLSL version: OpenGL ES GLSL ES 3.20
[09:00:47.063] GL vendor: ARM
[09:00:47.064] GL renderer: Mali-G52
E: [pulseaudio] module-rescue-streams.c: module-rescue-stream is obsolete and should no longer be loaded. Please remove it from your configuration.
E: [pulseaudio] module-console-kit.c: GetSessionsForUnixUser() call failed: org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.ConsoleKit was not provided by any .service files
E: [pulseaudio] module.c: Failed to load module "module-console-kit" (argument: ""): initialization failed.
W: [pulseaudio] server-lookup.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
W: [pulseaudio] main.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
[09:00:47.372] GL ES 3.2 - renderer features:
read-back format: ARGB8888
glReadPixels supports y-flip: no
wl_shm 10 bpc formats: yes
wl_shm 16 bpc formats: no
wl_shm half-float formats: no
internal R and RG formats: yes
OES_EGL_image_external: yes
wl_shm sub-image to texture: yes
[09:00:47.372] Using GL renderer
[09:00:47.434] event3 - adc-keys: is tagged by udev as: Keyboard
[09:00:47.434] event3 - adc-keys: device is a keyboard
[09:00:47.437] event0 - rk805 pwrkey: is tagged by udev as: Keyboard
[09:00:47.437] event0 - rk805 pwrkey: device is a keyboard
[09:00:47.439] event2 - hdmi_cec_key: is tagged by udev as: Keyboard
[09:00:47.440] event2 - hdmi_cec_key: device is a keyboard
[09:00:47.442] event4 - rk-headset: is tagged by udev as: Keyboard
[09:00:47.442] event4 - rk-headset: device is a keyboard
[ 6.078187] file system registered
[09:00:47.444] event1 - bt-powerkey: is tagged by udev as: Keyboard
[09:00:47.444] event1 - bt-powerkey: device is a keyboard
[09:00:47.514] libinput: configuring device "adc-keys".
[09:00:47.514] libinput: configuring device "rk805 pwrkey".
[09:00:47.514] libinput: configuring device "hdmi_cec_key".
[09:00:47.514] libinput: configuring device "rk-headset".
[ 6.120567] bcmdhd: loading out-of-tree module taints kernel.
[09:00:47.515] libinput: configuring device "bt-powerkey".
[09:00:47.515] Registered plugin API 'weston_drm_output_api_v1' of size 40
[ 6.137015] [dhd] _dhd_module_init: in Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240411-2)(d83d8d7)
[09:00:47.515] Color manager: no-op
[ 6.137015] /home/viewpro/RK3566_RK3568_Linux5.10_V1.2.0/external/rkwifibt/drivers/bcmdhd compiled on Nov 1 2024 at 12:42:22
[09:00:47.515] Compositor capabilities:
[ 6.137015]
arbitrary surface rotation: yes
[ 6.137088] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.36 (wlan=r892223-20231107-1)
screen capture uses y-flip: yes
[ 6.137180] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for index 0: 1102848(1077K)
cursor planes: yes
[ 6.137197] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
arbitrary resolutions: no
[ 6.137285] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=117, oob_irq_flags=0x4
view mask clipping: yes
[ 6.137295] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1
explicit sync: yes
[ 6.137303] [dhd] dhd_wifi_platform_load: Enter
color operations: no
[ 6.137310] [dhd] Power-up adapter 'DHD generic adapter'
presentation clock: CLOCK_MONOTONIC, id 1
[ 6.137540] [dhd] dummy_probe: func->num=0x1;
presentation clock resolution: 0.000000001 s
[ 6.137552] [dhd] dummy_probe: class=0xff; vendor=0x2d0; device=0xffff
[09:00:47.516] Loading module '/usr/lib/weston/desktop-shell.so'
[ 6.139820] [dhd] dummy_probe: func->num=0x2;
[ 6.139851] [dhd] dummy_probe: class=0xff; vendor=0x2d0; device=0xffff
Handling start for Wi-Fi/BT chip:
[ 6.140129] [dhd] dummy_probe: func->num=0x3;
Broadcom AP625X sdio 02d0:a9bf bcmdhd.ko # AP6255/AP6256/AP6745
[ 6.140152] [dhd] dummy_probe: class=0xff; vendor=0x2d0; device=0xffff
Starting Wi-Fi/BT...
[ 6.140237] [dhd] wifi_platform_set_power = 1, delay: 200 msec
Wi-Fi/BT module: bcmdhd.ko
[ 6.140247] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
Installing bcmdhd.ko ...
[ 6.140255] [WLAN_RFKILL]: rockchip_wifi_power: 1
[09:00:47.559] DRM: head 'HDMI-A-1' found, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
[ 6.140264] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
Supported EOTF modes: SDR
[ 6.140271] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[09:00:47.560] DRM: head 'DSI-1' found, connector 180 is connected, EDID make 'unknown', model 'unknown', serial ''
[ 6.181269] read descriptors
Supported EOTF modes: SDR
[ 6.181311] read strings
[09:00:47.560] launching '/usr/libexec/weston-keyboard'
[ 6.344053] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec
[09:00:47.563] launching '/usr/libexec/weston-desktop-shell'
[ 6.344083] [dhd] wifi_platform_bus_enumerate device present 1
[09:00:47.566] HDMI-A-1 using at least 2 buffers
[ 6.344091] [dhd] ======== Card detection to detect SDIO card! ========
[09:00:47.566] Output 'HDMI-A-1' attempts EOTF mode: SDR
[ 6.360438] [dhd] bcmsdh_register: register client driver
[09:00:47.566] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[ 6.360696] [dhd] bcmsdh_sdmmc_probe: Enter num=1
[09:00:47.567] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[ 6.360863] [dhd] bcmsdh_sdmmc_probe: Enter num=2
[09:00:47.567] Output HDMI-A-1 (crtc 71) video modes:
[ 6.360876] [dhd] bus num (host idx)=3, slot num (rca)=1, caps=0x4008010d
1920x1080@60.0, preferred, current, 148.5 MHz
[ 6.360884] [dhd] found adapter info 'DHD generic adapter'
1920x1080@60.0 16:9, 148.5 MHz
[ 6.360897] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 3, size 139264
1920x1080@59.9 16:9, 148.4 MHz
[ 6.360933] [dhd] succeed to alloc static buf
1920x1080i@60.0, 74.2 MHz
[ 6.360940] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 4, size 0
1920x1080i@60.0 16:9, 74.2 MHz
[ 6.360986] [dhd] sdioh_attach: set sd_f2_blocksize 256
1920x1080i@59.9 16:9, 74.2 MHz
[ 6.361013] [dhd] sdioh_attach: sd clock rate = 150000000
1920x1080@50.0 16:9, 148.5 MHz
[ 6.361276] [dhd] dhdsdio_probe : no mutex held
1920x1080i@50.0 16:9, 74.2 MHz
[ 6.361288] [dhd] dhdsdio_probe : set mutex lock
1680x1050@59.9, 119.0 MHz
[ 6.361373] [dhd] F1 signature read @0x18000000=0x15294345
1400x1050@59.9, 101.0 MHz
[ 6.363411] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2
1600x900@60.0, 108.0 MHz
[ 6.364153] [dhd] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
1280x1024@75.0, 135.0 MHz
[ 6.364250] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 7, size 42288
1280x1024@60.0, 108.0 MHz
[ 6.364285] [dhd] dhd_conf_set_chiprev : devid=0xa9bf, chip=0x4345, chiprev=9
1440x900@59.9, 88.8 MHz
[ 6.364332] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 0, size 10320
1280x800@59.9, 71.0 MHz
[ 6.364379] [dhd] dhd_ioctl_entry_local invalid parameter net 0000000000000000 dev_priv 0000000094cd3ebc
1152x864@75.0, 108.0 MHz
[ 6.364389] [dhd] CFG80211-ERROR) wl_is_fils_supported : FILS NOT supported, err -22
1280x720@60.0, 74.2 MHz
[ 6.364822] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 5, size 65536
1280x720@60.0 16:9, 74.2 MHz
[ 6.365220] [dhd] CFG80211-ERROR) wl_is_fils_supported : FILS NOT supported, err -19
1280x720@59.9 16:9, 74.2 MHz
[ 6.365921] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 19, size 65688
1280x720@50.0 16:9, 74.2 MHz
[ 6.366241] [dhd] dhd_attach(): thread:dhd_watchdog_thread:3e1 started
1024x768@75.0, 78.8 MHz
[ 6.366366] [dhd] dhd_attach(): thread:dhd_dpc:3e2 started
1024x768@60.0, 65.0 MHz
[ 6.366467] [dhd] dhd_attach(): thread:dhd_rxf:3e3 started
800x600@75.0, 49.5 MHz
[ 6.366486] [dhd] dhd_deferred_work_init: work queue initialized
800x600@60.3, 40.0 MHz
[ 6.366497] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
720x576@50.0 16:9, 27.0 MHz
[ 6.366504] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
720x480@60.0 4:3, 27.0 MHz
[ 6.366599] [dhd] sdioh_cis_read: func_cis_ptr[0]=0x10ac
720x480@60.0 16:9, 27.0 MHz
[ 6.371446] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 1, size 10300
720x480@59.9, 27.0 MHz
[ 6.371525] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 2, size 65536
720x480@59.9 16:9, 27.0 MHz
[ 6.371575] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
640x480@75.0, 31.5 MHz
[ 6.371676] [dhd] Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240411-2)(d83d8d7)
640x480@60.0 4:3, 25.2 MHz
[ 6.371676] /home/viewpro/RK3566_RK3568_Linux5.10_V1.2.0/external/rkwifibt/drivers/bcmdhd compiled on Nov 1 2024 at 12:42:22
640x480@59.9, 25.2 MHz
[ 6.371676]
640x480@59.9 4:3, 25.2 MHz
[ 6.372395] [dhd] Register interface [wlan0] MAC: 70:f7:54:9a:5f:9a
720x400@70.1, 28.3 MHz
[ 6.372395]
[09:00:47.568] associating input device event3 with output HDMI-A-1 (none by udev)
[ 6.372561] [dhd] [wlan0] wl_android_wifi_off : g_wifi_on=1 force_off=1
[09:00:47.568] associating input device event0 with output HDMI-A-1 (none by udev)
[ 6.372576] [dhd] dhd_bus_devreset: == Power OFF ==
[09:00:47.568] associating input device event2 with output HDMI-A-1 (none by udev)
[ 6.372742] [dhd] dhd_bus_stop: making DHD_BUS_DOWN
[09:00:47.568] associating input device event4 with output HDMI-A-1 (none by udev)
[ 6.372773] [dhd] bcmsdh_oob_intr_unregister: Enter
[09:00:47.568] associating input device event1 with output HDMI-A-1 (none by udev)
[ 6.372782] [dhd] bcmsdh_oob_intr_unregister: irq is not registered
[09:00:47.568] Output HDMI-A-1 changed to mirror output
[ 6.372794] [dhd] dhd_bus_devreset: making dhdpub up FALSE
[09:00:47.568] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[ 6.372802] [dhd] dhd_txglom_enable: enable 0
[09:00:47.568] DSI-1 using at least 2 buffers
[ 6.372809] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[09:00:47.569] Output 'DSI-1' attempts EOTF mode: SDR
[ 6.372843] [dhd] wifi_platform_set_power = 0, delay: 10 msec
[09:00:47.569] Output 'DSI-1' using color profile: stock sRGB color profile
[ 6.372853] [dhd] ======== PULL WL_REG_ON(-1) LOW! ========
[09:00:47.569] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[ 6.372861] [WLAN_RFKILL]: rockchip_wifi_power: 0
[09:00:47.570] Output DSI-1 (crtc 93) video modes:
[ 6.372868] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
1024x600@60.8, preferred, current, 51.0 MHz
[ 6.372874] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[09:00:47.570] associating input device event3 with output DSI-1 (none by udev)
[ 6.372881] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[09:00:47.570] associating input device event0 with output DSI-1 (none by udev)
[ 6.377829] dwc3 fcc00000.dwc3: device reset
[09:00:47.570] associating input device event2 with output DSI-1 (none by udev)
[ 6.383786] [dhd] wifi_platform_set_power = 0, sleep done: 10 msec
[09:00:47.570] associating input device event4 with output DSI-1 (none by udev)
[ 6.383813] [dhd] [wlan0] wl_android_wifi_off : out
[09:00:47.570] associating input device event1 with output DSI-1 (none by udev)
[ 6.384680] [dhd] Register interface [wlan1] MAC: 72:f7:54:9a:5f:9a
[09:00:47.570] Output 'DSI-1' enabled with head(s) DSI-1
[ 6.384680]
could not load cursor 'dnd-move'
[ 6.384713] [dhd] wl_android_post_init: 0
could not load cursor 'dnd-move'
[ 6.384721] [dhd] dhdsdio_probe : mutex is released.
could not load cursor 'dnd-copy'
[ 6.385416] [dhd] bcmsdh_sdmmc_probe: Enter num=3
could not load cursor 'dnd-none'
[ 6.386620] [dhd] _dhd_module_init: Exit err=0
could not load cursor 'dnd-copy'
[ 6.414439] [dhd] dhd_pri_open : no mutex held
could not load cursor 'dnd-none'
[ 6.414470] [dhd] dhd_pri_open : set mutex lock
Successfully init Wi-Fi for AP625X!
[ 6.414480] [dhd] [wlan0] dhd_open : Enter
Successfully initialized wpa_supplicant
[ 6.414488] [dhd] Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240411-2)(d83d8d7)
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
[ 6.414488] /home/viewpro/RK3566_RK3568_Linux5.10_V1.2.0/external/rkwifibt/drivers/bcmdhd compiled on Nov 1 2024 at 12:42:22
could not create XKB compose table for locale 'en_US.UTF-8'. Disabiling compose
[ 6.414488]
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
[ 6.414506] [dhd] dhd_open: ######### called for ifidx=0 #########
could not create XKB compose table for locale 'en_US.UTF-8'. Disabiling compose
[ 6.414523] [dhd] [wlan0] wl_android_wifi_on : in g_wifi_on=0
[ 6.414533] [dhd] wifi_platform_set_power = 1, delay: 200 msec
[ 6.414540] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 6.414547] [WLAN_RFKILL]: rockchip_wifi_power: 1
[ 6.414554] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 6.414562] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[ 6.444079] android_work: sent uevent USB_STATE=CONNECTED
[ 6.449173] android_work: sent uevent USB_STATE=CONFIGURED
[ 6.620459] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec
[ 6.620494] [dhd] sdio_sw_reset: call mmc_hw_reset
[ 6.840630] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 6.886664] mmc3: queuing unknown CIS tuple 0x80 (2 bytes)
[ 6.888546] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[ 6.890344] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[ 6.893561] mmc3: queuing unknown CIS tuple 0x80 (7 bytes)
[ 6.897295] mmc3: queuing unknown CIS tuple 0x81 (9 bytes)
[ 6.960254] mmc_host mmc3: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[ 6.970860] dwmmc_rockchip fe000000.dwmmc: Successfully tuned phase to 270
[ 6.971148] [dhd] sdioh_start: set sd_f2_blocksize 256
[ 6.971446] [dhd] dhd_bus_devreset: == Power ON ==
[ 6.971563] [dhd] F1 signature read @0x18000000=0x15294345
[ 6.975421] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2
[ 6.976681] [dhd] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 6.976778] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[09:00:48.724] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[ 6.976834] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
[09:00:48.725] Output 'HDMI-A-1' no heads left, disabling.
[ 6.976997] [dhd] dhd_conf_set_path_params : Final fw_path=/vendor/etc/firmware/fw_bcm43456c5_ag.bin
[09:00:48.725] Disabling output HDMI-A-1
[ 6.977007] [dhd] dhd_conf_set_path_params : Final nv_path=/vendor/etc/firmware/nvram_ap6256.txt
[09:00:48.745] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[ 6.977015] [dhd] dhd_conf_set_path_params : Final clm_path=/vendor/etc/firmware/clm_bcm43456c5_ag.blob
[ 6.977022] [dhd] dhd_conf_set_path_params : Final conf_path=/vendor/etc/firmware/config.txt
[ 6.978834] [dhd] dhd_os_open_image1: /vendor/etc/firmware/config.txt (240 bytes) open success
[ 6.979218] [dhd] dhd_conf_read_pm_params : PM = 0
[ 6.979236] [dhd] dhd_conf_read_pm_params : pm_in_suspend = 2
[ 6.979249] [dhd] dhd_conf_read_others : keep_alive_period = 120000
[ 6.979258] [dhd] dhd_conf_read_others : garp = 1
[ 6.979269] [dhd] dhd_conf_read_pm_params : suspend_bcn_li_dtim = 10
[ 6.979282] [dhd] dhd_conf_read_others : wl_preinit = pm2_sleep_ret=20
[ 6.979294] [dhd] dhd_conf_read_pkt_filter : pkt_filter_del id = 100 102 103 104 105 107
nl80211: kernel reports: Registration to specific type not supported
[ 6.979319] [dhd] dhd_conf_read_pkt_filter : pkt_filter_add[0][] = 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[ 6.979967] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43456c5_ag.bin (628872 bytes) open success
[ 6.980293] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43456c5_ag.bin (628872 bytes) open success
[ 6.980306] [dhd] dhdsdio_download_code_file Using SINGLE image (size 628872)
[ 7.051090] [dhd] dhd_os_open_image1: /vendor/etc/firmware/nvram_ap6256.txt (2732 bytes) open success
[ 7.051509] [dhd] #AP6256_NVRAM_V1.4_06112021
[ 7.052037] [dhd] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 7.141798] [dhd] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 7.142017] [dhd] bcmsdh_oob_intr_register: HW_OOB irq=117 flags=0x4
[ 7.143203] [dhd] wlc_ver_major 4, wlc_ver_minor 1
[ 7.143230] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 1
[ 7.143238] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[ 7.143893] [dhd] dhd_legacy_preinit_ioctls: use firmware generated mac_address 70:f7:54:9a:5f:9a
[ 7.144022] [dhd] dhd_apply_default_clm: Ignore clm file /vendor/etc/firmware/clm_bcm43456c5_ag.blob
[ 7.145541] [dhd] Firmware up: op_mode=0x0005, MAC=70:f7:54:9a:5f:9a
[ 7.149760] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 40 ret: -23
[ 7.152422] [dhd] arp_enable:1 arp_ol:0
[ 7.152451] [dhd] dhd_conf_add_pkt_filter : 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[ 7.156539] [dhd] Driver: 101.10.591.52.27 (20240409-1)(20240411-2)
[ 7.156539] [dhd] Firmware: wl0: Apr 1 2024 13:44:02 version 7.45.96.201 (gdb74b971) FWID 01-fe1c2a99 es7.c5.n4.a3
[ 7.156539] [dhd] CLM: 9.2.9 (2016-02-03 04:34:31)
[ 7.156780] [dhd] dhd_txglom_enable: enable 1
[ 7.156791] [dhd] dhd_conf_set_txglom_params : txglom_mode=copy
[ 7.156799] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0
[ 7.156805] [dhd] dhd_conf_set_txglom_params : txinrx_thres=128, dhd_txminmax=-1
[ 7.156812] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300
[ 7.156824] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1
[ 7.157836] [dhd] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[ 7.186698] [dhd] dhd_legacy_preinit_ioctls: Failed to get preserve log # !
[ 7.187011] [dhd] dhd_legacy_preinit_ioctls: d3_hostwake_delay IOVAR not present, proceed
[ 7.187293] [dhd] dhd_bus_check_srmemsize : srmem_size no need to change.
[ 7.209057] [dhd] dhd_conf_set_country : set country CN, revision 38
[ 7.211871] [dhd] dhd_conf_set_country : Country code: CN (CN/38)
[ 7.218352] [dhd] [wlan0] wl_android_wifi_on : Success
[ 7.263378] [dhd] CFG80211-ERROR) init_roam_cache : roamscan_mode iovar failed. -23
[ 7.263406] [dhd] CFG80211-ERROR) wl_cfg80211_up : Failed to enable RCC.
[ 7.265163] [dhd] [wlan0] dhd_open : Exit ret=0
[ 7.265189] [dhd] [wlan0] dhd_pri_open : tx queue started
[ 7.265196] [dhd] dhd_pri_open : mutex is released.
[ 7.273950] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[ 7.349644] [dhd] P2P interface registered
[ 7.383555] [BT_RFKILL]: bt shut off power
[ 7.398115] [dhd] WLC_E_IF: NO_IF set, event Ignored
[ 7.399420] [dhd] P2P interface started
[ 7.909725] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
[ 7.960448] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input!
[ 7.960510] [BT_RFKILL]: ENABLE UART_RTS
[ 8.057496] Freeing drm_logo memory: 1384K
[ 8.067072] [BT_RFKILL]: DISABLE UART_RTS
[ 8.067135] [BT_RFKILL]: bt turn on power
[ 8.067291] [BT_RFKILL]: Request irq for bt wakeup host
[ 8.067723] [BT_RFKILL]: ** disable irq
[09:00:49.763] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
Supported EOTF modes: SDR
[09:00:49.763] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:49.763] HDMI-A-1 using at least 2 buffers
[09:00:49.763] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:49.763] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:49.764] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:49.764] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080@59.9 16:9, 148.4 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080i@59.9 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1680x1050@59.9, 119.0 MHz
1400x1050@59.9, 101.0 MHz
1600x900@60.0, 108.0 MHz
1280x1024@75.0, 135.0 MHz
1280x1024@60.0, 108.0 MHz
1440x900@59.9, 88.8 MHz
1280x800@59.9, 71.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@59.9 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1024x768@75.0, 78.8 MHz
1024x768@60.0, 65.0 MHz
800x600@75.0, 49.5 MHz
800x600@60.3, 40.0 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@60.0 4:3, 27.0 MHz
720x480@60.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
640x480@75.0, 31.5 MHz
640x480@60.0 4:3, 25.2 MHz
[ 8.479918] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
640x480@59.9, 25.2 MHz
640x480@59.9 4:3, 25.2 MHz
720x400@70.1, 28.3 MHz
[09:00:49.764] Output HDMI-A-1 changed to mirror output
[09:00:49.764] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
###AMPAK FW Auto detection patch version = [v1.1 20161117]###
FW folder path = /lib/firmware
[ 8.593371] of_dma_request_slave_channel: dma-names property of node '/serial@fe650000' missing or empty
proc_reset[ 8.593408] dw-apb-uart fe650000.serial: failed to request DMA, use interrupt mode
chip id = BCM4345C5
FW path = /lib/firmware/BCM4345C5.hcd
send hci_download_minidriver[09:00:51.170] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[ 9.719573] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:51.170] Output 'HDMI-A-1' no heads left, disabling.
[09:00:51.170] Disabling output HDMI-A-1
[09:00:51.198] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
proc_resetDone setting line discpline
Successfully init BT for AP625X!
Done
[09:00:52.208] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
Supported EOTF modes: SDR
[09:00:52.208] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:52.208] HDMI-A-1 using at least 2 buffers
[09:00:52.208] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:52.208] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:52.209] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:52.209] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080@59.9 16:9, 148.4 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080i@59.9 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1680x1050@59.9, 119.0 MHz
1400x1050@59.9, 101.0 MHz
1600x900@60.0, 108.0 MHz
1280x1024@75.0, 135.0 MHz
1280x1024@60.0, 108.0 MHz
1440x900@59.9, 88.8 MHz
1280x800@59.9, 71.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@59.9 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1024x768@75.0, 78.8 MHz
1024x768@60.0, 65.0 MHz
800x600@75.0, 49.5 MHz
800x600@60.3, 40.0 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@60.0 4:3, 27.0 MHz
720x480@60.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
640x480@75.0, 31.5 MHz
[ 10.923781] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
640x480@60.0 4:3, 25.2 MHz
640x480@59.9, 25.2 MHz
640x480@59.9 4:3, 25.2 MHz
720x400@70.1, 28.3 MHz
[09:00:52.209] Output HDMI-A-1 changed to mirror output
[09:00:52.209] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:00:53.630] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[ 12.179513] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:53.630] Output 'HDMI-A-1' no heads left, disabling.
[09:00:53.630] Disabling output HDMI-A-1
[09:00:53.659] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:54.669] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
Supported EOTF modes: SDR
[09:00:54.670] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:54.670] HDMI-A-1 using at least 2 buffers
[09:00:54.670] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:54.670] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:54.670] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:54.670] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080@59.9 16:9, 148.4 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080i@59.9 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1680x1050@59.9, 119.0 MHz
1400x1050@59.9, 101.0 MHz
1600x900@60.0, 108.0 MHz
1280x1024@75.0, 135.0 MHz
1280x1024@60.0, 108.0 MHz
1440x900@59.9, 88.8 MHz
1280x800@59.9, 71.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@59.9 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1024x768@75.0, 78.8 MHz
1024x768@60.0, 65.0 MHz
800x600@75.0, 49.5 MHz
800x600@60.3, 40.0 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@60.0 4:3, 27.0 MHz
720x480@60.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
640x480@75.0, 31.5 MHz
640x480@60.0 4:3, 25.2 MHz
[ 13.386635] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
640x480@59.9, 25.2 MHz
640x480@59.9 4:3, 25.2 MHz
720x400@70.1, 28.3 MHz
[09:00:54.671] Output HDMI-A-1 changed to mirror output
[09:00:54.671] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:00:56.077] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[ 14.626187] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:56.077] Output 'HDMI-A-1' no heads left, disabling.
[09:00:56.077] Disabling output HDMI-A-1
[09:00:56.105] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:57.116] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
Supported EOTF modes: SDR
[09:00:57.117] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:57.117] HDMI-A-1 using at least 2 buffers
[09:00:57.117] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:57.117] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:57.117] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:57.117] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080@59.9 16:9, 148.4 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080i@59.9 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1680x1050@59.9, 119.0 MHz
1400x1050@59.9, 101.0 MHz
1600x900@60.0, 108.0 MHz
1280x1024@75.0, 135.0 MHz
1280x1024@60.0, 108.0 MHz
1440x900@59.9, 88.8 MHz
1280x800@59.9, 71.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@59.9 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1024x768@75.0, 78.8 MHz
1024x768@60.0, 65.0 MHz
800x600@75.0, 49.5 MHz
800x600@60.3, 40.0 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@60.0 4:3, 27.0 MHz
720x480@60.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
640x480@75.0, 31.5 MHz
640x480@60.0 4:3, 25.2 MHz
[ 15.832472] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
640x480@59.9, 25.2 MHz
640x480@59.9 4:3, 25.2 MHz
720x400@70.1, 28.3 MHz
[09:00:57.118] Output HDMI-A-1 changed to mirror output
[09:00:57.118] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:00:58.537] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[ 17.086164] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:58.537] Output 'HDMI-A-1' no heads left, disabling.
[09:00:58.537] Disabling output HDMI-A-1
[09:00:58.567] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:59.576] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
Supported EOTF modes: SDR
[09:00:59.576] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:59.576] HDMI-A-1 using at least 2 buffers
[09:00:59.577] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:59.577] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:59.577] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:59.577] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080@59.9 16:9, 148.4 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080i@59.9 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1680x1050@59.9, 119.0 MHz
1400x1050@59.9, 101.0 MHz
1600x900@60.0, 108.0 MHz
1280x1024@75.0, 135.0 MHz
1280x1024@60.0, 108.0 MHz
1440x900@59.9, 88.8 MHz
1280x800@59.9, 71.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@59.9 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1024x768@75.0, 78.8 MHz
1024x768@60.0, 65.0 MHz
800x600@75.0, 49.5 MHz
800x600@60.3, 40.0 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@60.0 4:3, 27.0 MHz
720x480@60.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
640x480@75.0, 31.5 MHz
[ 18.292004] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
640x480@60.0 4:3, 25.2 MHz
640x480@59.9, 25.2 MHz
640x480@59.9 4:3, 25.2 MHz
720x400@70.1, 28.3 MHz
[09:00:59.577] Output HDMI-A-1 changed to mirror output
[09:00:59.578] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:01:00.983] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[ 19.532876] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:01:00.984] Output 'HDMI-A-1' no heads left, disabling.
[09:01:00.984] Disabling output HDMI-A-1
[09:01:01.010] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:02.020] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
Supported EOTF modes: SDR
[09:01:02.021] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:02.021] HDMI-A-1 using at least 2 buffers
[09:01:02.021] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:01:02.021] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:01:02.021] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:01:02.021] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080@59.9 16:9, 148.4 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080i@59.9 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1680x1050@59.9, 119.0 MHz
1400x1050@59.9, 101.0 MHz
1600x900@60.0, 108.0 MHz
1280x1024@75.0, 135.0 MHz
1280x1024@60.0, 108.0 MHz
1440x900@59.9, 88.8 MHz
1280x800@59.9, 71.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@59.9 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1024x768@75.0, 78.8 MHz
1024x768@60.0, 65.0 MHz
800x600@75.0, 49.5 MHz
800x600@60.3, 40.0 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@60.0 4:3, 27.0 MHz
720x480@60.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
640x480@75.0, 31.5 MHz
640x480@60.0 4:3, 25.2 MHz
[ 20.737984] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
640x480@59.9, 25.2 MHz
640x480@59.9 4:3, 25.2 MHz
720x400@70.1, 28.3 MHz
[09:01:02.022] Output HDMI-A-1 changed to mirror output
[09:01:02.022] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:01:03.820] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[ 22.369490] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:01:03.820] Output 'HDMI-A-1' no heads left, disabling.
[09:01:03.820] Disabling output HDMI-A-1
[09:01:03.840] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:04.859] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
Supported EOTF modes: SDR
[09:01:04.860] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:04.860] HDMI-A-1 using at least 2 buffers
[09:01:04.860] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:01:04.860] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:01:04.860] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:01:04.860] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080@59.9 16:9, 148.4 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080i@59.9 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1680x1050@59.9, 119.0 MHz
1400x1050@59.9, 101.0 MHz
1600x900@60.0, 108.0 MHz
1280x1024@75.0, 135.0 MHz
1280x1024@60.0, 108.0 MHz
1440x900@59.9, 88.8 MHz
1280x800@59.9, 71.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@59.9 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1024x768@75.0, 78.8 MHz
1024x768@60.0, 65.0 MHz
800x600@75.0, 49.5 MHz
800x600@60.3, 40.0 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@60.0 4:3, 27.0 MHz
720x480@60.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
640x480@75.0, 31.5 MHz
640x480@60.0 4:3, 25.2 MHz
[ 23.577237] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
640x480@59.9, 25.2 MHz
640x480@59.9 4:3, 25.2 MHz
720x400@70.1, 28.3 MHz
[09:01:04.861] Output HDMI-A-1 changed to mirror output
[09:01:04.861] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[ 33.923794] vcc3v3_lcd1_n: disabling
/bin/list-iodomain.sh version: V1.0.1
Get CHIP ID: rk356x
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXX PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!!
XXXXXXXXXX 请务必检查IO电源域配置 !!!!!!!!!!!!!!!
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Get IO DOMAIN VALUE:
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
注意事项：PMUIO1/PMUIO2 固定不可配
VCCIO2电平由硬件FLASH_VOL_SEL决定:
当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平;
当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平;
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
pmuio2_vsel: 3.3V
vccio7_vsel: 3.3V
vccio6_vsel: 1.8V
vccio5_vsel: 3.3V
vccio4_vsel: 3.3V
vccio3_vsel: 3.3V
vccio2_vsel: 3.3V
vccio1_vsel: 3.3V
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
root@rk3566-buildroot:/#
root@rk3566-buildroot:/#
root@rk3566-buildroot:/# /bin/list-iodomain.sh version: V1.0.1
Get CHIP ID: rk356x
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXX PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!!
XXXXXXXXXX 请务必检查IO电源域配置 !!!!!!!!!!!!!!!
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Get IO DOMAIN VALUE:
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
注意事项：PMUIO1/PMUIO2 固定不可配
VCCIO2电平由硬件FLASH_VOL_SEL决定:
当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平;
当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平;
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
pmuio2_vsel: 3.3V
vccio7_vsel: 3.3V
vccio6_vsel: 1.8V
vccio5_vsel: 3.3V
vccio4_vsel: 3.3V
vccio3_vsel: 3.3V
vccio2_vsel: 3.3V
vccio1_vsel: 3.3V
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
/bin/list-iodomain.sh version: V1.0.1
Get CHIP ID: rk356x
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXX PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!!
XXXXXXXXXX 请务必检查IO电源域配置 !!!!!!!!!!!!!!!
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Get IO DOMAIN VALUE:
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
注意事项：PMUIO1/PMUIO2 固定不可配
VCCIO2电平由硬件FLASH_VOL_SEL决定:
当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平;
当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平;
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
pmuio2_vsel: 3.3V
vccio7_vsel: 3.3V
vccio6_vsel: 1.8V
vccio5_vsel: 3.3V
vccio4_vsel: 3.3V
vccio3_vsel: 3.3V
vccio2_vsel: 3.3V
vccio1_vsel: 3.3V
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
root@rk3566-buildroot:/#
root@rk3566-buildroot:/#
[END] 2024/11/2 9:47:19